Gtco Super L VI - Users Guide Uživatelský manuál

Super L VI 1

Super L VI 10 Installing the TabletWorks Driver Insert the CD into the CD-ROM drive on your computer. The installer will autoload. If it does

Super L VI 11 USB Connection Super L VI USB port connection is USB 1.1 and 2.0 compatible. When the digitizer is connected to the USB port, Wi

Super L VI 12 Transducer Connection 1. If you are using a corded transducer, connect the cursor or pen to the appropriate jack on the digitize

Super L VI 13 Using the SuperSet Menu (RS-232 Only) The SuperSet Menu is the row of buttons printed across the top of the digitizer. It allows

Super L VI 14 buttons through are active only after clicking on the button to activate Select Mode. Resetting Super L VI The Super L VI c

Super L VI 15 Configuring Super L VI for Specific Applications To configure your Super L VI for use with specific applications: 1. In Table 1,

Super L VI 16 Table 1: SuperSet Menu Codes for Selected Applications

Super L VI 17

Super L VI 18

Super L VI 19

Super L VI 2 Table of Contents Introduction Parts Checklist What You Will Need to Use Super L VI PC Requirements For a USB Inst

Super L VI 20

Super L VI 21

Super L VI 22

Super L VI 23

Super L VI 24

Super L VI 25

Super L VI 26 Table 2: Configuration Details for SuperSet Menu Codes NOTE: Max = 100 coordinates/second lpi = lines per inch lpmm = lines pe

Super L VI 27

Super L VI 28

Super L VI 29

Super L VI 3 Output Format Options Mode Options Using the Tablet Configuration Utilities Learning the Basics

Super L VI 30

Super L VI 31 Super L VI Tones The Super L VI produces an alarm in the form of audio tones to inform you of various events. The table below de

Super L VI 32 The configuration parameters for the Super L VI are divided into three categories:  Communication Options  Output Format Opti

Super L VI 33 ASCII formats can be modified by including or excluding a button code, decimal point, carriage return or line feed, depending on

Super L VI 34 Using the Tablet Configuration Utilities If your application is not represented in the SuperSet Menu and does not have a SuperSe

Super L VI 35 6. Select a predefined through , SuperSet Code, or select one of the User Defined through , SuperSet Codes to customize. a.

Super L VI 36 Learning the Basics You will find that using your DrawingBoard VI tablet is as easy or easier, than using a mouse. The DrawingBo

Super L VI 37 Lite Touch Pen The lite touch pen is available only in the cordless version. It is similar to the click tip pen, except that it

Super L VI 38 Cleaning the Cursor To clean the cursor body, use a mild cleanser. Do not spray the cleanser directly on the cursor – instead,

Super L VI 39 To replace the batteries: 1. Unscrew the pen cap. Hold the pen from the bottom and gently slide off the pen cover to expose the

Super L VI 4 Limited Warranty for the Super L VI 52 Introduction Super L VI belongs to a class of computer input devices called graphics

Super L VI 40 To replace the batteries: 1. Place the cursor face down in the palm of your hand. Use a Phillips screwdriver to remove the two

Super L VI 41 2. Read the topics below to check for a solution to your problem. Work through the troubleshooting flowcharts on the following

Super L VI 42 Changing the Frequency of the Cordless Pen Press both side buttons and the tip simultaneously and hold for approximately three se

Super L VI 43 Software Checklist Does the tablet work with some software? If your tablet currently works with some software packages, you know

Super L VI 44 Troubleshooting Chart The following table lists common Super L VI problems, their causes and their solutions. Problem Cause Solut

Super L VI 45 Unable to use the entire tablet surface may conflict with the display. Incorrect format selected. Software application set

Super L VI 46 Procedure B: Troubleshooting

Super L VI 47

Super L VI 48 Returning your Tablet for Repair If you believe you have a defective tablet, first see all topics in this section (above) and vis

Super L VI 49 television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the i

Super L VI 5 Before setting up Super L VI, you should determine:  The requirements of the digitizing software application you’re using  Whe

Super L VI 50

Super L VI 51 Japan European Union Emission Directive This product is in conformity with the protection requirements of EU Council Directive 8

Super L VI 52 Bescheinigung des Herstellers/Importeurs Heirmit wird bescheinigt, dass der/die/das Super L VI (Geraet, Typ, Bezeichnung) im Ueb

Super L VI 53 Limited Warranty for Super L VI GTCO CalComp by Turning Technologies, Inc. warrants these products to be free from defects in ma

Super L VI 54 2. Costs for initial technical adjustments (set up), including adjustment of user controls. 3. Certain shipping charges. (Paym

Super L VI 55 Notice Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above ex

Super L VI 56 Corporate Headquarters 14557 N. 82nd Street Scottsdale, Arizona 85260 Tel: 1-866-746-3015 Support: 1-866-746-3015 Fax: 480-99

Super L VI 6 What You Will Need to Use the Super L VI Super L VI is equipped with both a USB interface and an RS-232 serial interface, which r

Super L VI 7 Overview The Super L VI consists of: Active Area The drawing area – the Active Area – is the portion of the tablet surface design

Super L VI 8 Transducer Two types of transducers can be used with the Super L VI: pens and cursors. Both are available in corded and cordless

Super L VI 9 Attaching the Optional Accessory Tray, Plan Holder or Table Feet Additional T-Nuts have been included in the perimeter mounting ch